This tutorial shows you how to build a shape design from a basic wireframe model This task shows how to create swept surfaces and fillets on both sides of the. You can create a swept surface by sweeping out a profile in planes normal to a spine curve while taking other user-defined parameters (such as guide curves. This task shows you how to create swept surfaces that use an explicit profile. These profiles must not be T- The Swept Surface Definition dialog box appears .

Author: Shakaramar Nimuro
Country: Lithuania
Language: English (Spanish)
Genre: Automotive
Published (Last): 21 August 2013
Pages: 419
PDF File Size: 8.81 Mb
ePub File Size: 5.42 Mb
ISBN: 539-9-97610-731-7
Downloads: 84455
Price: Free* [*Free Regsitration Required]
Uploader: Tagul

When creating a sweep, you are cata able to preview the four solutions based on the values given for the Angle. By default, the angular correction is set to 0.

These parameters allow you to position the profile in the first sweep plane. This may be necessary catia v5 sweep tutorial small discontinuities are detected with regards to the spine tangency or the reference surface’s normal.

do anyone have the full tutorial of sweep in wireframe and surface design catia v5??

The following futorial are available: However, in a few cases, even though the spine is not tangent continuous, the swept surface is computed: Select the xy plane as the reference surface. Generally speaking, the spine must present a tangency continuity.

catia v5 sweep tutorial

If you want to go back to the original profile, deselect Position profile. If you modify the length value catia v5 sweep tutorial clicking Previewand the swept surface to be generated has no twisted area, the generated catia v5 sweep tutorial surface will still be cut.

Note that the selection is still available. If Fill twisted areas is checked, while the Add cutter button is clicked, the created cutters define a filled area. The law can be negative, providing the curves are curvature continuous.

All SWEEP surface commands in CATIA V5

If a plane normal catia v5 sweep tutorial the spine intersects one of the guiding curves at more than one points, the application chooses the closest point to the spine point. When there is only one relimiter, you are sweep to choose the direction of the sweep by clicking the green arrow.


Deselect Remove cutters on Preview. Their default positions are the maximal zone delimiters out of which they cannot be dragged. You can also specify anchor points for each guide.

If needed, select a Spine. Here is an example with the With pulling direction sub-type, DemoProfile1 as the ProfileDemoGuide1 as the Guidexy plane for the Directionand 45deg for the Angle. The With pulling Direction subtype is equivalent to the With reference surface subtype with a reference plane normal to the pulling direction.

T hese modes force the chosen catia v5 sweep tutorial. This capability is available with all types of swept surfaces, except for: Otherwise, the cutters define a cutting zone. Use the displayed 3D cutters to enlarge the zone in order to correctly build the missing area. Select a Direction zx plane.

This option is unavailable for the following profile types: Use the Remove catia v5 sweep tutorial areas management option to start the operation again.

All SWEEP surface commands in CATIA V5 | GrabCAD Tutorials

The angular definition defined by the law if selected applies to catia v5 sweep tutorial projection of the normal to the reference element in the sweeping plane normal to the spine.

In the Smooth sweeping section, you can check: When there is only one relimiter, you are able to choose the direction of the sweep by clicking the green arrow. You can sweep an explicit profile: Four types of laws are available: The orange arrow corresponds to the current solution. The anchor points catia v5 sweep tutorial computed as follows: If no spine is selected, the guide curve is implicitly used as the spine.

Here is an example with DemoGuide2. In the Smooth sweeping catia v5 sweep tutorial, you can check: These cutters are stored in the model as points on curve with ratio parameters when the guide curve is not closed. If the profile is manually positioned defining anchor points will position v55 profile between the guides, matching the anchor points with guide intersection points, prior to performing the sweeping operation.


If Similar to guide fails then the Standard tutkrial strategy is applied.

Creating Swept Surfaces Using an Explicit Profile

Tangency discontinuous spine with connex swept segments the sweep is created. Three guides and Two guides and tangency surface subtypes conical profile: You can sweep an implicit circular profile along a spine. If the spine presents a tangency continuity, tutoriql surface presents at least a point continuity.

Angular correction to smooth the sweeping motion along the reference surface. In each sweeping plane, the profile is rotated around the anchor point so that the anchor direction linked to this profile is aligned with the two guide curves, from Guide Curve 1 to Guide Curve 2. Remove catia v5 sweep tutorial areas management: If you do not explicitly catia v5 sweep tutorial anchor points or anchor direction, they are automatically computed if the profile is planar.

Click the Explicit profile icon and select With with catia v5 sweep tutorial guide curves from the Subtype drop-down list. The profile position may be fixed with respect to the guide curve positioned profile or user-defined in the first sweep plane CATIA P2 only.

Click Preview again in the Swept Surface Definition dialog box. The profile is swept out in planes normal to the spine. Relimiters catia v5 sweep tutorial be selected on a closed curve curve, spine, or default spine.

Moreover, it can automatically detect planer surfaces if they exist in the swept surface.