CD4001 PDF

; Manufacturer: Major Brands; Manufacturer no.: CD Texas Instruments [ KB ]; Data Sheet (current) [ KB ]; National Semiconductor [ KB ]. The CDBC and CDBC quad gates are monolithic complementary MOS (CMOS) integrated circuits con- structed with N- and P-channel enhancement. The CD quad gate is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P-channel enhancement mode transistors.

Author: Shakarn Doubar
Country: Seychelles
Language: English (Spanish)
Genre: Politics
Published (Last): 18 November 2005
Pages: 299
PDF File Size: 1.28 Mb
ePub File Size: 1.60 Mb
ISBN: 216-6-86582-217-1
Downloads: 36923
Price: Free* [*Free Regsitration Required]
Uploader: Matilar

Generating time delay with IC. Resistor Resistor is a passive component used to control current in a circuit.

Group all Htabs Electronics. Thus a particular value of resistor, for fixed voltage, limits the current through it.

Understanding NOR Gate (CD4001)

It consists of 4 independent NOR gate in a single chip. Choosing Motor For Robots. Interface GPS with Arduino. Latest Blogs Web Browsers: They are omnipresent in Skip to main content. Now logic 0 is on pin 5 ad 6 we will receive logic 1 at pin 4 of NI2. As a result current start following in capacitor and capacitor starts to charge.

CD – Quad 2-In NOR Gate

If we assume pin 9 of Cd40011 to be high then also we will get pin 0 to be high and low as you can now see from truth table. In the diagram above consider that we have supply logic low to pin1 of NI1 as a result we will receive logic 1 in output pin 3 if you have assume pin 2 of NI1 be low.

  K2996 MOSFET PDF

But as capacitor charges voltage on resistor drops to half the power supply NI1 detects a high on in its input pin 2 as a result logic 0 appear on pin 3. The circuit describe below can be used in many application like it can we use as fake light to create an impression that alarm has been fitted or you can use it in your vehicles when your car broke down as it will give eye catching appearance to the car passing near to dc4001 vehicle.

Each gate has 2 inputs and 1 output. What is Web Browser. Light cx4001 using photodiode.

Circuit Diagram for Understanding NOR Gate (CD)

Interface SD Card with Arduino. And if any the inputs are high we will receive the low output. From above we can see that for a certain period of time circuit will work and then goes off. In first gate NI1 pin cd401 and 2 are for inputs and pin 3 is for output.

SPI Module of Arduino.

Negative is connected to pin 7 and pin 14 is connected to power supply. Resistor is a passive component used to control current in a circuit. It has small notch on one side which is identified as pin 1. In another words we will receive the high output when both the signals goes low. As a result pin 8 is also high and now again assume pin 9 to be low now we will receive 0 at output pin of NI3 and as a result output pin ofNI4 will receive high and LED start glowing.

  THE 8085 MICROPROCESSOR ARCHITECTURE PROGRAMMING AND INTERFACING BY PDF DOWNLOAD

This means that we will receive 6V at pin 4. As we can see in the truth table it will provide the output equal to one when both of the input is low.

Atmospheric Vortex Engine Twister Power. Working voltage range of IC is from 5V to 15V.

As you can see in the circuit below. Choosing Battery for Robots.

Access Denied

Now voltage on pin 8 is also low at this time and assume voltage on pin 9 to be low as a result we will receive high at pin 10 of NI3 which also make pin 12 and 13 of NI4 to high and we will receive low on pin 11 as you can see from truth table and LED connected to it will not glow.

IC consists of 14 pin where pin numbers 7 and 14 are connected to battery or DC power supply.

It can deliver approx. Its resistance is given by the ratio of voltage applied across its terminals to the current passing through it.